Fender Flares 4 Piece 2,5cm wide Wrangler JL year 18-24
Jeep Wrangler JL year 18-24
Jeep Wrangler JL Unlimited year 18-24
Fender flare - 4 pieces - 25 millimeters wide
Fender flare especially for the Jeep Wrangler JL (2018-). It is attached to the outer edge of the fender by means of industrial adhesive strips and a special gel adhesive. The sealing lip, which fits closely to the vehicle, ensures a clean finish and prevents the penetration of dirt.
Details:
• The extensions are glued to the outside of the outer edge of the mudguard of the chassis.
• the fender extensions are not paintable
• inexpensive, flexible and therefore almost indestructible rubber extensions
• optimal e.g. for track fender flare by spacers or wider tires & rims
Scope of delivery:
• 4 pieces (2x length 1010mm and 2x length 840mm)
• 25 mm (the vehicle is widened by 25 mm per fender / 50 mm per axle)
• German TÜV Süd test report (TÜV-Süd, Westendstr. 199, 80686 Munich, Germany, test report 16-00074-CP-BWG)
TÜV registration:
• You will receive a german TÜV Süd test report with the delivery of the extensions. The registration of the fender extensions is not necessary, this is also stated in the report, but we know from experience and from many customer messages that the police officers like to see such a TÜV confirmation again. Only then there is really no trouble with the inspection service and therefore we have a TÜV Süd report prepared.
Mounting:
• The ambient temperature and the temperature of the components or mounting surface must be a minimum of 20° Celsius during assembly and at least 24 hours afterwards
• The surfaces on the vehicle for assembly must be rust-free, smooth, thoroughly cleaned and free of grease
• After removing the carrier foil, the fender flare must be pressed against the surface with high and even pressure for approx. 1 minute
• The ends of the fender widening can be adjusted to the vehicle look with a sharp carpet knife
• We recommend that you leave the vehicle for at least 6 hours after assembly
• The final strength of the glued joints is only reached after 48 hours
• Please do not wash the vehicle for at least 48 hours
• For some widths, some mounting situations, structured surfaces or if the mounting instructions cannot be observed, additional fastening with e.g. self-tapping screws or body adhesive is required
Installation Instruction:
Jeep Wrangler JL Unlimited year 18-24
Fender flare - 4 pieces - 25 millimeters wide
Fender flare especially for the Jeep Wrangler JL (2018-). It is attached to the outer edge of the fender by means of industrial adhesive strips and a special gel adhesive. The sealing lip, which fits closely to the vehicle, ensures a clean finish and prevents the penetration of dirt.
Details:
• The extensions are glued to the outside of the outer edge of the mudguard of the chassis.
• the fender extensions are not paintable
• inexpensive, flexible and therefore almost indestructible rubber extensions
• optimal e.g. for track fender flare by spacers or wider tires & rims
Scope of delivery:
• 4 pieces (2x length 1010mm and 2x length 840mm)
• 25 mm (the vehicle is widened by 25 mm per fender / 50 mm per axle)
• German TÜV Süd test report (TÜV-Süd, Westendstr. 199, 80686 Munich, Germany, test report 16-00074-CP-BWG)
TÜV registration:
• You will receive a german TÜV Süd test report with the delivery of the extensions. The registration of the fender extensions is not necessary, this is also stated in the report, but we know from experience and from many customer messages that the police officers like to see such a TÜV confirmation again. Only then there is really no trouble with the inspection service and therefore we have a TÜV Süd report prepared.
Mounting:
• The ambient temperature and the temperature of the components or mounting surface must be a minimum of 20° Celsius during assembly and at least 24 hours afterwards
• The surfaces on the vehicle for assembly must be rust-free, smooth, thoroughly cleaned and free of grease
• After removing the carrier foil, the fender flare must be pressed against the surface with high and even pressure for approx. 1 minute
• The ends of the fender widening can be adjusted to the vehicle look with a sharp carpet knife
• We recommend that you leave the vehicle for at least 6 hours after assembly
• The final strength of the glued joints is only reached after 48 hours
• Please do not wash the vehicle for at least 48 hours
• For some widths, some mounting situations, structured surfaces or if the mounting instructions cannot be observed, additional fastening with e.g. self-tapping screws or body adhesive is required
Installation Instruction: